OTT MXQ PRO 4K Firmware update issue

Hello Everyone,

I have recently bought my one of those boxes and everything was fine with the box until screen was going pink from time to time. I found out the I need to enable Force RGB output which was meant to be under More Settings > Display. It was not there and I found that I need to update the box. I found an update that matched the version I had on my box P201 I followed the tutorial to go into recovery and update, unfortunately it bricked my box and the screen went black. Then, I found that I need to use the Amlogic burning tool and install new image, I could not find a matching image so I used one from entertaiment box, then Hugsun, then Eny, then few others from some Russian forums. The change of the firmware worked fine, however none of them have the option to Force RGB and my Remote does not work with any of them, so I have to update it with config I found on internet, but the remote still does not power off and the media buttons are not functioning.

Can anyone suggest a firmware with Force RGB output that will work with my box ? It would be perfect if it would also support power on and off using my remote, but not necessary. I am mainly after the Force RGB option.

Image with the old configuration before any update

http://ift.tt/29hJuIO

Romote config:

#************************************************* ************************************************** ******
#this file is configuration for each factory remote device
# work_mode 0 :software mode 1 :hardware mode
# repeat_enable 0 :disable repeat 1 :enable repeat
#
# factory_code each device has it's unique factory code.
# pattern:custom_code(16bit)+index_code(16bit)
# examble: 0xff000001 = 0xff00(custom cod) 0001 (index)
#
# release_delay unit:ms.release will report from kernel to user layer after this period of time
# from press or repeat triggered.
#
# debug_enable 0 :debug disable 1 :debug disable
#
# SW MODE:
# bit_count how many bits in each frame
# tw_leader_act time window for leader active
# tw_bit0 time window for bit0 time.
# tw_bit1 time window for bit1 time
# tw_repeat_leader time window for repeat leader
# REG
# reg_base_gen set value for PREG_IR_DEC_BASE_GEN
# reg_control set value for PREG_IR_DEC_CONTROL
# reg_leader_act set value for PREG_IR_DEC_LEADER_ACTIVE
# reg_leader_idle set value for PREG_IR_DEC_LEADER_IDLE
# reg_repeat_leader set value for PREG_IR_DEC_REPEAT_IDLE
# reg_bit0_time set value for PREG_IR_DEC_BIT0_TIME
#************************************************* ************************************************** **********
#amlogic NEC remote
factory_code = 0x7f800001
work_mode = 0
repeat_enable = 1
repeat_delay = 40
repeat_peroid = 39
release_delay = 121
debug_enable = 1

fn_key_scancode = 0x15
left_key_scancode = 0x1c
right_key_scancode = 0x48
up_key_scancode = 0x44
down_key_scancode = 0x1d
ok_key_scancode = 0x5c
pageup_key_scancode = 0x04
pagedown_key_scancode = 0x1b

mouse_begin
0 0x1c
1 0x48
2 0x44
3 0x1d
mouse_end

key_begin
0x4d 113
0x56 114
0x4e 115
0x25 105
0x26 103
0x27 106
0x28 108
0x0d 97
0x1b 158
0x53 102
0x51 704
0x49 139
0x52 388
0x31 2
0x32 3
0x33 4
0x34 5
0x35 6
0x36 7
0x37 8
0x38 9
0x39 10
0x30 11
0x58 389
0x44 14
0xbd 122
0xbb 123
0x09 393
0x11 390
0x54 391
0x4f 392





key_end
repeat_key_begin
0x4d 113
0x56 114
0x4e 115
0x25 105
0x26 103
0x27 106
0x28 108
0x0d 28
0x1b 158
0x53 102
0x51 704
0x49 139
0x52 388
0x31 2
0x32 3
0x33 4
0x34 5
0x35 6
0x36 7
0x37 8
0x38 9
0x39 10
0x30 11
0x58 389
0x44 111
0xbd 122
0xbb 123
0x09 164
0x11 390
0x54 391
0x4f 392
repeat_key_end

from xda-developers http://ift.tt/29efcDc
via IFTTT